D&D - ClariSea SK-5000 Automatic Filter System
The ClariSea SK-5000 Automatic Filter System automatically removes particulates from your water that would normally turn into nitrates and phosphates.
The SK-5000 Automatic Filter System will leave your tank with brilliantly clean water which will help increase your lighting penetration, reduce maintenance, and the best benefit of all, let you see your corals and fish with fewer particulates in the way.
Suitable for use in marine aquariums, freshwater aquariums, fish-breeding systems, and propagation systems for corals.
Features:
- High volume filtration capacity
- Minimal installation footprint
- Completely replaces the need for filter socks
- Self-assembly for easy cleaning
- Multiple installation options
- Automatic advance of dirty fleece
- Multi-function smart controller
- End of roll audible alarm
- Filter jam/float error/water depth alarm
- Phosphate-free fleece material
- Special low-odor fleece material
- Integrated fail-safe overflow
- Silencer plates for quiet operation
- Water bypass system
- flow rate: up to 5,000 l/h (1320 US gph)
- Particle size removal: down to 20 microns
- Maximum submerged water depth: 20cm (8”)
- Hang-on bracket height adjustment: up to 12cm (4”)
- Maximum sump glass thickness for hang on bracket: 13mm (1/2")
- Recommended aquarium size at 5 x tank turn over (5000l/hr) = 1000lt
- Recommended aquarium size at 4 x tank turn over (5000l/hr) = 1250lt
- Inlet connection: 32mm ( 1" fitting for the U.S )
- Filter fleece: 15cm (6”) width – length 25m (82ft)
- Dimension:
- Base: 145 x 255mm
- Top: 225 x 255mm
- Height: 455mm
How do I install the Clarisea Roll Filter.
The Gen2 ClariSea is very flexible and easy to position within your sump:
- You can hang it on the back, front or sides of the most sumps.
- You can freestand it on the base of a shallow sump with a water level below 200mm.
- you can freestand it on a box or shelf in deeper sumps.
- You can feed it from the front or from the back.
- You can feed water from the top, side or at an angle.
- You can even pump feed it.
Smart Controller Functions
Buttons & Indicators
:
Motor button
- Option to manually advance fleece
Alarm button
- Press alarm button for 1 - 2 seconds will turn off audible alarm, but alarm condition will still be present
- Red LED still flashing
- Automatic advance of fleece disabled.
- Motor button will still function as manual advance.
-
Pressing the alarm button for > 5 seconds:- Full reset - completely clearing alarm state
- Disconnecting power: performs reset as above.
Normal Operation
:
Initialization (Power on or reset)
- Blue/Red LED both flash for 5 times (audible alarm will sound with each flash)
- Blue LED will remain on.
Motor Advance
- Manual or automatic, Blue LED flashes
Possible Alarm Conditions:
Possible roll jam/motor failure (float held in up position for more than 5 seconds)
- Red alarm LED will flash
- Audible alarm will sound for 2 seconds every 5 seconds
- Automatic advance of fleece disabled.
Possible fleece empty (float not triggered within 8 hours)
- Blue/Red LED both flashing, audible alarm will sound for 1 second every 2 seconds
- Automatic advance of fleece disabled.
Possible installation error (float not triggered with 48 hours after initial set-up or reset)
- Red LED will flash at 10-second intervals (audible alarm will sound with each flash)
- Automatic advance of fleece disabled.
Important note: Only use the 20mm bolt to attach the motor to the Clarisea, do not use the 30mm bolt , this is for the clean fleece. Using the 30mm long bolt to attach the motor will result in damage to the motor assembly.
