ClariSea SK-3000 Automatic Filter System G2 - D-D

Dhs. 1,522.00

D&D - ClariSea SK-3000 Automatic Filter System

The ClariSea SK-3000 Automatic Filter System is a high-efficiency water filtration system that effectively removes suspended particles such as microalgae, detritus, food, organic waste, and gravel dust from the water column.

Suitable for use in marine aquariums, freshwater aquariums, fish-breeding systems, and propagation systems for corals.

Features:

  • High volume filtration capacity
  • Minimal installation footprint
  • Completely replaces the need for filter socks 
  • Self-assembly for easy cleaning
  • Multiple installation options 
  • Automatic advance of fleece when dirty.
  • Phosphate-free fleece material
  • Special low-odour fleece material
  • Integrated fail-safe overflow 
  • Silencer plates for quiet operation
  • Water bypass system

Specifications:

  • Recommended flow rate: 3,000 l/h (800 US gph)
  • Particle size removal: down to 20 microns 
  • Maximum submerged water depth: 20cm (8”)
  • Hang-on bracket height adjustment: up to 12cm (4”) 
  • Maximum sump glass thickness for hang on bracket: 13mm (1/2")
  • Recommended aquarium size at 5 x tank turn over (3000l/hr) = 600lt
  • Recommended aquarium size at 4 x tank turn over (3000l/hr) = 750lt
  • Inlet connection: 32mm ( 1" fitting)
  • Filter fleece: 10cm (4”) width – length 25m (82ft)
    • Dimensions
    • Base: 145 x 205mm
    • Top: 225 x 205mm
    • Height: 455mm

How do I install the ClariSea Roll Filter?

The Gen2 ClariSea is very flexible and easy to position within your sump:

  • You can hang it on the back, front, or sides of the most sumps.
  • You can free stand it on the base of a shallow sump with a water level below 200mm.
  • you can free stand it on a box or shelf in deeper sumps.
  • You can feed it from the front or from the back.
  • You can feed water from the top, side, or at an angle.
  • You can even pump feed it.

Motor button
  • Option to Manually advances fleece motor
Alarm button
  • Press alarm button for 1 - 2 seconds will turn off an audible alarm, but alarm condition will still be present
    • Red LED still flashing
    • Automatic advance of fleece disabled.
    • Motor button will still function as manual advance.
  • Pressing the alarm button for > 5 seconds:- Full reset - completely clearing alarm state
  • Disconnecting power: performs reset as above.

Normal Operation
:

Initialization (Power on or reset)
  • Blue/Red LED both flashes 5 times (audible alarm will sound with each flash)
  • Blue LED will remain on.

Motor Advance
  • Manual or automatic, Blue LED flashes

Possible Alarm Conditions:

Possible roll jam/motor failure (float held in up position for more than 5 seconds)
  • Red alarm LED will flash
  • Audible alarm will sound for 2 seconds every 5 seconds
  • Automatic advance of fleece disabled.
Possible fleece empty (float not triggered within 8 hours)
  • Blue/Red LED both flashing, audible alarm will sound for 1 second every 2 seconds
  • Automatic advance of fleece disabled.
Possible installation error (float not triggered with 48 hours after initial set-up or reset)
  • Red LED will flash at 10-second intervals (audible alarm will sound with each flash)
  • Automatic advance of fleece disabled.
    Important note: Only use the 20mm bolt to attach the motor to the Clarisea, do not use the 30mm bolt , this is for the clean fleece. Using the 30mm long bolt to attach the motor will result in damage to the motor assembly.